Type examination for EAC conformity assessment

In order to apply for the EAC Certificate, the EAC Declaration or the GOST R Certificate, the products must pass appropriate tests.

Performance of type examinations

Only accredited testing laboratories are allowed to perform type examinations for EAC certification. An accredited laboratory means that:

• it possesses the respective accreditation of the Federal Service for Accreditation (Rosaccreditation for example)
• it is listed in the unique register of testing laboratories (centers) of the Eurasian Union

The requirements for the testing laboratories are specified in the following norms

• GOST R 51000.4-2008 General requirements for accreditation of testing laboratories.
• GOST ISO / IEC 17025-2019 eneral requirements for the competence of testing and calibration laboratories

Type examinations may only be performed on the manufacturer’s site and with the manufacturer’s test equipment, if the test equipment has been approved in advance by the certification body and an accredited expert for the EAC certification is present during the type examinations to ensure the objectivity of the type examinations.

If the EAC declaration is conducted according to scheme 1D or 2D, the examinations may also be carried out in the manufacturer’s own production laboratory. However, the technical regulations must also be taken into account. According to the following technical regulations, type examinations may only be performed in an accredited test laboratory:

• TR CU 007/2011 On safety of the products for children and teenagers
• TR CU 009/2011 On safety of perfumes and cosmetic products
• TR CU 017/2011 On safety of light industry products
• TR CU 025/2012 On safety of furniture

Type of tests

In general, there is just one type of tests, which is the safety test. Depending on the product, also other safety indicators are taken into account, such as electrical, chemical, microbiological safety etc. However, tests are still subdivided in two further categories:

• the sample is tested, but not destroyed: this applies for expensive or unique products
• the sample is destroyed and then disposed by the laboratory. Information on this will be given always before the order.

Testing procedure

For EAC certification, only the certification body may refer the samples to the laboratory for testing. The certification body collects a set of documents received from the manufacturer (or his authorized representative) and the importer.

In order to carry out type examinations, the following documents must be sent with the sample:

• Application for certification examination prepared by the certification body
• Instruction manual in Russian
• if necessary also technical specification if the product is manufactured in Russia

In any case, a detailed list of the documents required by the Technical Regulations, should be provided.

The type examination is carried out according to a specific program and method, as specified in the norms that can be found in the appendix of the Technical Regulations. The standards were established on the basis of the generally accepted method of certification testing and depending on the type of product. The table shows some standards for specific product groups.

The program and methodology can be developed both by the manufacturer and by the experts of the certification body.

In some cases it is not necessary to carry out a type examination, if this is not required by the technical regulation. For example, for the conformity assessment procedure according to scheme 9c or 6c no type examination is needed.

Samples for the testing procedure

There are certain rules according to which samples should be sent for testing. These rules, as well as answers to questions about the correct selection of samples, the required number of samples, the exact testing procedure, etc., can be found here

In order to simplify the process of sending samples, we have compiled a list of advice, which you can find in this article.

Test report

The results of the tests are entered in the test report.

A test report is an official document which is issued by the testing laboratories after having conducted the certification tests. It confirms the compliance of the product with the specified technical standards.

A certificate of conformity or declaration is issued on the basis of the expert opinion prepared together with the test report.

The test report must contain the following information:

1. basis of the tests
2. information on the manufacturer of the products
3. description of the samples
4. testing methods
5. date
6. results

Period of validity of a test report

The test report is valid for one year from the date of issue if the protocol has been applied for as part of mandatory certification. For further requests, the test reports will be issued for six years. If you require the test report for voluntary certification, the validity period is agreed upon in consultation with the notified body.

The laboratory is obliged to keep a copy of the protocol for at least 3 years.

Duration and costs of EAC type examination

The duration and costs associated with type examination for EAC certification or EAC declaration depend on the required quantity and complexity of the examinations. The exact conditions of the EAC certification are always determined individually based on the required documentation.